Simply soak a washcloth in water and ring it out a bit so it’s not sopping wet. Put the damp washcloth on the affected area. The water will wick through the wood, and that’s fine. Now, with your iron on its highest setting, place it on the damp washcloth over the affected area, and make small movements back and forth and in circles. Press down firmly and continue until your wash cloth is dry. It won’t take long to evaporate. At this point, the wood fibers are absorbing the water and should expand back to where they were originally. Continue this process and repeat by adding more water until the dents rise up to be flush with the rest of the material.
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.

I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.


My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
Basically, I created a linear outfeed area, which includes the miter-saw station with folding wings, tablesaw with folding outfeed table, and my large router table, all in a line along the 20-ft. wall and set at the same height. The miter-saw station converts easily for use with a mortiser—with workpiece support on both sides—and it also accepts a minilathe. I even planned a location for all of the tools, blades, and jigs used with the tablesaw: on the operator side, for easy access.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
I’m 91 years old, but I still enjoy spending time in the wood shop. I like to make wooden toys and give them to my great-grandkids and charity groups. One trick I’ve learned over the years is to use emery boards—the kind for filing fingernails— to sand small parts. Emery boards come in different sizes, and some are more abrasive than others, so I keep an assortment on hand. — Joe Aboussleman

Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
Efficiency does not always increase with experience, because as our woodshops grow older, they sometimes become unnecessarily rearranged or cluttered. And if you’re just now setting up your first woodshop, this shop layout should give you a great starting point. Each picture represents one half of a standard two-car garage. Click on the images for a larger view, and if anything is unclear, ask a question in the comments field!
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.

If your shop will be attached to your house or another struc­ture, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.


“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant


With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
Before you bid in an online auction, check the site’s rules of operation. At some sites, a winning bid is a binding contract, which can be a problem if you can’t inspect the tool before you purchase it. Don’t forget shipping costs. In some cases they can exceed the cost of the tool. Also, make sure the tool you’re buying will run on the power you have in your shop. Many former industrial tools run on 240v single-phase power. If your shop doesn’t have 240v service, you’ll need to factor in the cost of upgrading before deciding to buy. You don’t want to saddle yourself with a tool you can’t use, no matter how good the price.

Each entry must feature some kind of inlay. This can be wood, glass, metal, etc. Epoxy pours are not allowed per /u/kevin0611's request. An epoxy pour does not count as an inlay for the sake of this contest. (Example would be cutting a pattern on CNC or by hand then filling with a colored epoxy to give the illusion that it's inlay.) Bowties, marquetry, and banding are good examples of allowed inlay in this contest.


The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively win­dowless north walls may be a place to arrange wood storage or mechanicals.
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
In this video Dave Heller shares an introduction to wood veneering and wood inlay for furniture making. What is veneering and inlay? They are traditional methods used to embellish and beautify furniture. Veneering is the process of gluing thin slices of attractive (and often rare) wood onto core panels. Inlay involves insetting wood, precious stones, etc. into the wood. Here's a prime example of one of Dave's boxes that incorporates both techniques: Here is an example

Pocket screw joinery is a system—employing special drill and driver bits—used to join boards or pieces of plywood to one another. Installing pocket screws involves using a jig to drill a sharply angled, 15-degree hole through the back of one board, then driving a special screw through that hole into the second board to draw them tightly together. Learn how to use pocket screws here. It’s often used in cabinetmaking and furniture building. Here’s how to build cabinets with pocket screws. The term “pocket” comes from the design of the hole which contains an upper “pocket” for the head of the screw to push against; this pocket also hides the head of the screw.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
×