The layout of a workshop will be based, in part, on how it will be used — whether for carpentry, fine woodworking, metalwork or other activities. Regardless of category, however, it's important to keep in mind the principles of efficiency and organization. A layout that's clearly thought out in terms of functionality will make all the difference in creating a workspace that offers a pleasant surrounding as well as a space that's conducive to work.
Pocket screw joinery is a system—employing special drill and driver bits—used to join boards or pieces of plywood to one another. Installing pocket screws involves using a jig to drill a sharply angled, 15-degree hole through the back of one board, then driving a special screw through that hole into the second board to draw them tightly together. Learn how to use pocket screws here. It’s often used in cabinetmaking and furniture building. Here’s how to build cabinets with pocket screws. The term “pocket” comes from the design of the hole which contains an upper “pocket” for the head of the screw to push against; this pocket also hides the head of the screw.
In this video Dave Heller shares an introduction to wood veneering and wood inlay for furniture making. What is veneering and inlay? They are traditional methods used to embellish and beautify furniture. Veneering is the process of gluing thin slices of attractive (and often rare) wood onto core panels. Inlay involves insetting wood, precious stones, etc. into the wood. Here's a prime example of one of Dave's boxes that incorporates both techniques: Here is an example
Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.
The table saw is best suited for making rip cuts, which are cuts along the length of the board, but with a crosscutting jig, the table saw can do just as well on crosscuts, which are cuts across the board. I even use the table saw for resawing thick lumber into thinner boards. The bandsaw is usually the tool for resawing, but any lumber under 6″ wide can be resawn on a 10″ table saw by cutting from both sides of the board.
Cedars are strong, aromatic softwoods that are capable of enduring outdoor elements, the most common of which is the Western Red Cedar. Western Red Cedar can sustain wet environments without succumbing to rot, and as a result is commonly used for outdoor projects such as patios, outdoor furniture, and building exteriors. This wood can be easily found at most home centers for a moderate price.
It has made me really think about doing things in an order which optimizes the switching around of machinery. One thing I did do which has really helped and that I would add to your list is SOUND PROOFING! Didn’t mean to yell there.. lol. Sound proofing has has allowed me to keep the workshop operations from bothering the rest of the family when I am in my man-room.
I could write a whole post on wood species as each species has unique characteristics and traits. But, one of the most common types of wood used in DIY projects and furniture building is pine wood (a softwood). Pine is an affordable and readily available option at your local home improvement store and it comes in many sizes. I highly recommend using pine for beginner woodworking projects. Then, as you improve your skill, try working with some different wood species!
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percentage of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both differ depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
Second is the operating space around the machine. When the table saw is used to cut a piece of four-by-eight-foot plywood, the tool space increases geometrically, as the thirty-two-square-foot sheet of stock is pushed and pulled through the blade. Even if you’re not planning on using your table saw to cut plywood, you need to allow ripping and crosscutting space. This means that in front of and beyond the blade, you need distances at least as great as the length of the longest board you’ll need to rip; and that you’ll require space for cutoff work on either side of the saw.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
There is significant evidence of advanced woodworking in ancient Egypt. Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off serious cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bottom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thickness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop without excessive grunting, so that made it very simple to install. The planer has a significant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
Commonly used woodworking tools included axes, adzes, chisels, pull saws, and bow drills. Mortise and tenon joints are attested from the earliest Predynastic period. These joints were strengthened using pegs, dowels and leather or cord lashings. Animal glue came to be used only in the New Kingdom period. Ancient Egyptians invented the art of veneering and used varnishes for finishing, though the composition of these varnishes is unknown. Although different native acacias were used, as was the wood from the local sycamore and tamarisk trees, deforestation in the Nile valley resulted in the need for the importation of wood, notably cedar, but also Aleppo pine, boxwood and oak, starting from the Second Dynasty.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but outside the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials movement. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key storage, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs.
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular ﬁnishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each ﬁnish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and ﬁnish combinations. Plus: How to stain wood evenly.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Along the opposite long wall are the planer, combination sander, drill press, bandsaw, workbench, and compressor. Each tool has dust-collection hookups and storage space to keep the relevant tools, bits, blades, and fixtures nearby. The planer is the only tool I have to roll out into the middle of the room to use, which takes about a minute, including connecting the dust-collection hose.
The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a concrete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
In addition to sheer power, look for a model with a built-in thermostat so you can set it and forget it. This convenience feature is well worth it so you don’t have to stop what you’re doing mid-project to manually turn your heater on and off to maintain your desired temp. A good garage heater will mount to the wall or ceiling to save space and will come with a durable housing and full safety screen to keep dust and wood chips from reaching the heating elements and starting a fire.